Skip to content Skip to sidebar Skip to footer

what does the hair dryer do to the iphone 4s to make the wifi work

Introduction

A common trouble in the iPhone 4S, sometimes the Wi-Fi button volition be grayed out and unclickable. This problem seems to be related to thermal shock — the trouble may be temporarily fixed by simply putting the phone in the fridge for 15 minutes, or under a lamp for thirty minutes.

If this is the example, then the necessary permanent solution is to reflow the Murata SW SS1830010 Wi-Fi chip on the logic board.

  1. Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

    • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion bombardment tin can catch burn down and/or explode if accidentally punctured.

    • Power off your iPhone before first disassembly.

    • Remove the two iii.6 mm Pentalobe P2 screws next to the dock connector.

    • Be sure the driver is well-seated when removing Pentalobe screws—they are easy to strip.

  2. Push the rear panel toward the top edge of the iPhone. The panel will move about 2 mm.

    • Push the rear panel toward the tiptop edge of the iPhone.

    • The console will move about two mm.

  3. Pull the rear panel away from the back of the iPhone, being careful not to damage the plastic clips attached to the rear panel.

    • Pull the rear panel away from the back of the iPhone, being careful non to impairment the plastic clips attached to the rear panel.

    • Remove the rear panel from the iPhone.

  4. Remove the following screws securing the battery connector to the logic board: One 1.7 mm Phillips screw

    • Remove the post-obit screws securing the battery connector to the logic lath:

    • One ane.7 mm Phillips screw

    • I 1.5 mm Phillips screw

  5. Carefully push the pressure contact away from the battery connector until it slides free from its position. Remove the pressure contact. Remove the pressure contact.

    • Carefully button the pressure level contact away from the battery connector until it slides free from its position.

    • Remove the force per unit area contact.

  6. Use a plastic opening tool to gently pry up the battery connector from its socket on the logic board. Place the tip of the tool between the loudspeaker enclosure and the metal cover of the connector, and lift the bottom edge of the connector first. The battery connector comes off vertically from the logic board. Do not apply force sideways.

    • Use a plastic opening tool to gently pry up the battery connector from its socket on the logic board.

    • Place the tip of the tool between the loudspeaker enclosure and the metallic cover of the connector, and lift the bottom edge of the connector first.

    • The battery connector comes off vertically from the logic board. Practice not apply force sideways.

    • Be conscientious not to pry at the battery connector socket itself, or information technology may detach from the logic lath. There are four very small solder points pending this mistake!

  7. During reassembly, be sure to carefully position the pressure contact back in place. It should rest on top of the Philips screw post shown, and the gold contact should point towards the battery connector. Be sure to clean the pressure contact with a degreaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to create wireless interference.

    • During reassembly, be sure to carefully position the force per unit area contact back in place. Information technology should remainder on top of the Philips screw post shown, and the aureate contact should point towards the battery connector.

    • Be certain to clean the pressure level contact with a degreaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to create wireless interference.

  8. Insert the edge of a plastic opening tool between the battery and the outer case near the bottom of the iPhone. Run the plastic opening tool along the right edge of the battery and pry up at several points to completely separate it from the adhesive securing it to the outer case.

    • Insert the edge of a plastic opening tool between the battery and the outer case almost the lesser of the iPhone.

    • Run the plastic opening tool along the correct edge of the battery and pry up at several points to completely split information technology from the agglutinative securing it to the outer case.

    • If the agglutinative is too strong, utilise a few drops of loftier concentration (over 90%) isopropyl alcohol under the edge of the battery.

    • Wait about one minute for the booze solution to weaken the agglutinative.

    • Use the flat end of a plastic opening tool to gently lift the battery.

    • Don't try to forcefully lever the battery out. If needed, employ a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

    • If at that place'due south whatsoever alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry out before installing your new battery.

  9. Use the exposed clear plastic pull tab to peel the battery off the adhesive securing it to the iPhone. Be careful not to pull the plastic pull tab too hard as it can be ripped off very easily.

    • Use the exposed articulate plastic pull tab to peel the bombardment off the adhesive securing it to the iPhone.

    • Be careful not to pull the plastic pull tab too difficult as it can be ripped off very easily.

    • Remove the battery.

    • If your replacement bombardment came in a plastic sleeve, remove it earlier installation by pulling information technology away from the ribbon cable.

    • If your replacement bombardment came with an uncreased cable, carefully crease the cable into the proper shape before installing the battery into the phone.

    • While installing the replacement bombardment, temporarily connect the battery connector to the phone to ensure proper alignment. Once the battery is glued in place, disconnect the battery connector.

    • Perform a hard reset afterward reassembly. This can prevent several issues and simplify troubleshooting.

  10. Remove the following screws securing the dock connector cable cover to the logic board: One 1.5 mm Phillips screw

    • Remove the following screws securing the dock connector cable cover to the logic board:

    • One 1.5 mm Phillips screw

    • One 1.ii mm Phillips screw

    • Remove the metal dock connector cable cover.

  11. Use the edge of a plastic opening tool to pry the dock cable up from its socket on the logic board.

    • Use the border of a plastic opening tool to pry the dock cable up from its socket on the logic board.

  12. Peel the dock connector cable off the adhesive securing it to the logic board and the side of the speaker enclosure.

    • Peel the dock connector cable off the adhesive securing it to the logic board and the side of the speaker enclosure.

  13. Use the edge of a plastic opening tool to pry the cellular antenna cable up from its socket on the logic board. De-route the cellular antenna cable out from under the metal fingers attached to the logic board.

    • Use the edge of a plastic opening tool to pry the cellular antenna cable up from its socket on the logic board.

    • De-road the cellular antenna cablevision out from under the metal fingers attached to the logic board.

  14. Use a SIM eject tool or a paperclip to eject the SIM and its tray. This may require a significant amount of force.

    • Use a SIM eject tool or a paperclip to eject the SIM and its tray.

    • This may require a pregnant amount of force.

    • Remove the SIM and its tray.

  15. Remove the five cables near the top of the logic board in the following order: Headphone jack/volume button cable

    • Remove the v cables near the top of the logic board in the following club:

    • Headphone jack/volume button cablevision

    • Front facing camera cablevision

    • Digitizer cablevision

    • Display data cable

    • Ability push button cable (located underneath the headphone jack/volume button cable as shown in the second picture show.)

    • To disconnect the cables, apply the edge of a plastic opening tool to gently elevator their connectors upwards and out of the sockets on the logic board.

    • Be conscientious not to break whatsoever of the small-scale and fragile surface mountain components every bit yous disconnect the cables.

  16. Remove the 1.5 mm Phillips screw securing the grounding clip to the logic board near the headphone jack.

    • Remove the i.5 mm Phillips screw securing the grounding prune to the logic lath near the headphone jack.

  17. Use the tip of a spudger to pry the small grounding clip up off the logic board. Carefully grasp the grounding clip and remove it from the iPhone.

    • Use the tip of a spudger to pry the small-scale grounding clip up off the logic board.

    • Carefully grasp the grounding clip and remove it from the iPhone.

    • Earlier reassembly, be certain to clean all metal-to-metal contact points on the grounding clip (not the mating halves of connectors) with a de-greaser such every bit windex or isopropyl alcohol. The oils on your fingers take the potential to crusade grounding issues.

    • Remove the 4.8 mm collision screw near the headphone jack.

    • Standoff screws are all-time removed using a collision screwdriver or bit.

    • In a compression, a small flathead screwdriver will do the job—but use extra caution to ensure it doesn't slip and damage surrounding components.

  18. Use the edge of a plastic opening tool to disconnect the Wi-Fi antenna from the logic board.

    • Utilize the edge of a plastic opening tool to disconnect the Wi-Fi antenna from the logic board.

  19. If present, peel the piece of black tape covering the hidden screw near the power button. Remove the 2.6 mm Phillips screw securing the logic board near the power button.

    • If present, skin the piece of blackness record covering the subconscious screw virtually the power push.

    • Remove the 2.six mm Phillips screw securing the logic board near the ability button.

    • (Use caution when removing this screw and removing the power contact held by it; the contact tab will come up loose with the spiral)

    • Notice the minor prophylactic bumper under the screen & digitizer cables (which are discrete at tiptop above the Q-lawmaking). This bumper can autumn off of the logic board when removed or get stuck to the cables and fall off later.

  20. Remove the following screws securing the logic board to the case:

    • Remove the post-obit screws securing the logic lath to the case:

    • I 2.v mm Phillips screw nearly the vibrator motor

    • One ii.iv mm Phillips screw

    • 1 3.6 mm standoff forth the side of the logic board nearest the battery opening.

    • Utilize a standoff driver bit and driver handle to remove the single three.6 mm standoff screw.

    • In a pinch, a pocket-size flathead screwdriver volition practice the job—only use actress circumspection to ensure it doesn't slip and damage surrounding components.

  21. Carefully lift the logic board from the end closest to the speaker enclosure and slide it away from the top edge of the iPhone.

    • Carefully elevator the logic board from the stop closest to the speaker enclosure and slide it away from the top border of the iPhone.

    • Remove the logic board.

    • Before reassembly, be certain to clean all metal-to-metal contact points on the logic board (not the mating halves of connectors) with a de-greaser such equally windex or isopropyl booze. The oils on your fingers take the potential to crusade grounding issues.

    • There is a modest condom bumper that sits on the pinnacle edge of the logic lath where the digitizer and screen cables come through the instance. It protects the cables as they curve over the elevation of the logic board. This can either get stuck to the cables or fall off the logic board when it comes out. Look back over step 22 for more details.

  22. Be sure not to lose the small grounding finger for the rear facing camera near the power button. This finger rests on top of the PCB, screwed down, and covered with the adhesive black plastic tape.

    • Be sure not to lose the small grounding finger for the rear facing camera near the power push. This finger rests on acme of the PCB, screwed downwards, and covered with the adhesive black plastic tape.

  23. Remove the adhesive protection on the Wi-Fi/bluetooth chip. Now we can see the Murata  SS1830010 chip. Now we can see the Murata  SS1830010 chip.

    • Remove the adhesive protection on the Wi-Fi/bluetooth chip.

    • Now we can see the Murata SS1830010 chip.

  24. Put the logic board in a PCB holder or small vise, to safely hold it while reflowing (it's going to get hot!). Protect the logic board with Kapton tape that has good insulating and temperature characteristics (temperature range: −269 to +400 °C). Protect the logic board with Kapton tape that has good insulating and temperature characteristics (temperature range: −269 to +400 °C).

    • Put the logic board in a PCB holder or small vise, to safely hold it while reflowing (it's going to get hot!).

    • Protect the logic lath with Kapton tape that has proficient insulating and temperature characteristics (temperature range: −269 to +400 °C).

  25. Now we need a hot air rework station with a small nozzle:

    • At present nosotros need a hot air rework station with a small nozzle:

    • The nozzle's size must exist 1/two or ane/four of the chip size.

  26. Edit: the correct temperature is almost 180-200 °C because around the chip there is a little black protection that can go under the chip. Set a low air flow: 1 or 2 (on a 1 to 7 scale). Now, doing circular movement, you have to reflow for 4-5 minutes.

    • Edit: the right temperature is most 180-200 °C because around the scrap there is a little black protection that tin can get under the chip.

    • Set a low air catamenia: one or 2 (on a 1 to 7 scale).

    • Now, doing circular movement, you lot have to reflow for four-5 minutes.

    • Exist conscientious to reflow just the Wi-Fi chip and non any of the surrounding ICs or circuits.

    • After 5 minutes, gradually subtract the temperature from 200 to 0 °C.

  27. After reflowing, wait ten minutes to allow the logic board to cool before handling it.

    • After reflowing, look ten minutes to allow the logic lath to absurd before treatment information technology.

    • Remember to put on the protective sticker dorsum on the Wi-Fi chip before reassembling the telephone.

  28. Here is the final result. Here is the final result.

    • Hither is the concluding consequence.

  29. These are the pictures before and after the reflow: In the first image, the Wi-Fi color is light grey (not working).

    • These are the pictures before and after the reflow:

    • In the showtime paradigm, the Wi-Fi colour is light grey (not working).

    • In the 2d image, the Wi-Fi color is dark grey (working).

Conclusion

To reassemble your device, follow these instructions in opposite lodge.

Embed this guide

Choose a size and re-create the code below to embed this guide every bit a pocket-size widget on your site / forum.

Preview

evansinces1988.blogspot.com

Source: https://www.ifixit.com/Guide/How+to+Fix+iPhone+4S+Wi-Fi+Grayed+Out/22167

Post a Comment for "what does the hair dryer do to the iphone 4s to make the wifi work"